Drawing standard notes full#

DETAILS NOT SHOWN ARE SIMILAR IN CHARACTER TO THOSE DETAILED. THE EXTERIOR WALL AS SHOWN SHALL BE COMPLETE SYSTEM INCLUDING ALL HOT DIPPED GALVANISED STEEL SUPPORTS, STIFFENERS, FASTENERS, SEALANT, JOINERY, MISC, PIECES, AND MATERIAL THICKNESS AS REQUIRED TO FORM HIGH QUALITY SYSTEM IN ACCORDANCE WITH THE SPECIFICATIONS AND THE PROFILES SHOWN.Ģ.

ALL BLOCKWALLS INDICATED ON PLAN ARE TO EXTEND TO THE SOFFIT OF THE SLAB, EXCEPT INTERNAL TOILET PARTITION, INTERNAL KITCHEN PARTITION, INTERNAL OFFICE PARTITIONS AND SMALL SPACES SUCH AS STORES. ALL BLOCKWALLS ENCLOSING THE FIRE ZONES SHALL BE LIGHT WEIGHT CONCRETE BLOCKWALL AND EXTENDED UP TO THE SOFFIT OF THE SLAB TO PROVIDE SPECIFIED FIRE RATINGĤ. REFER SCHEDULE OF WALL TYPES FOR DIFFERENT WALL SITUATIONS.ģ. AT ONE OR BOTH SIDES OF WALL OPENINGS AND AT WALL INTERSECTIONS.ĪLL CONTROL JOINTS SHOULD CONTINUE ALL THROUGH VERTICALLY.ĪLL CONTROL JOINTS ARE TO BE FILLED WITH APPROVED COMPRESSIBLE FILLER ANDĪLL EXPOSED SURFACES TO BE SEALED WITH APPROVED SEALANT AND BACK-UP ROD.Ģ.9000 MM SPACING AT LONG STRAIGHT WALLS,.NOTES APPEARING ON VARIOUS DRAWINGS FOR DIFFERENT SYSTEMS AND MATERIALS ARE TO BE REVIEWED, COORDINATED AND ARE TO BE APPLIED TO ALL RELATED DRAWINGS AND DETAILS. THE CONTRACTOR SHALL SUBMIT SAMPLES AND SHOP DRAWINGS FOR ALL WORKS WITH ALL NECESSARY DETAILS AND DESIGN INFORMATION FOR APPROVAL.Ģ3. FOR AREAS WITHOUT SUSPENDED CEILING HAVING EXPOSED SLAB AND BEAMS, WALL FINISH MATERIAL SHALL BE FROM FLOOR LEVEL TO BOTTOM OF SLAB LEVEL. CONTRACTOR TO LOCATE ALL ACCESS PANEL IN THE GYPSUM BOARD CEILING FOR SERVICES ACCESS.Ģ1. OPENINGS IN FIRE RATED WALLS & SLABS SHALL BE PROVIDED WITH FIRE SMOKE SEALS OF THE SAME FIRE RATING AS OF THE WALLS & SLABS THEY PENETRATE THROUGH.Ģ0. ALL FIRE DOORS SHALL HAVE SMOKE SEAL INTEGRAL WITH IT.ġ9. ALL SHAFTS SHALL BE SEALED AT BOTTOM & TOP TO PROVIDE 2 HRS. ALL BLOCKWALLS ENCLOSING THE FIRE ZONES SHALL BE LIGHT WEIGHT CONCRETE BLOCKWALL AND EXTENDED UP TO THE SOFFIT OF THE SLAB TO PROVIDE 2 HRS FIRE RATING.ġ6. REFER SCHEDULE OF WALL TYPES FOR DIFFERENT WALL SITUATIONS.ġ5. ALL UNDIMENSIONED WALL SHOULDERS SHALL BE 100MM WIDEġ4. ABOVE SUSPENDED CEILING LEVEL (ELEVATION) OR AS INDICATED.ġ3. ALL WALL FINISHES OR CEMENT PLASTERING WORKS ARE TO BE EXTENDED 10 CM.

ALL PLASTERED SURFACES SHALL BE PAINTED.ġ2. ALL ALUMINUM TRIMS SHALL BE POWDER COATED FINISH.ġ1. ANY DISCREPANCY BETWEEN THESE DRAWINGSAND DOCUMENTS SHOULD BE REPORTED TO THE ENGINEER FOR CLARIFICATION AND VERIFICATION.ġ0. ARCHITECTURAL DRAWINGS MUST ALWAYS BE READ IN CONJUNCTION WITH ALL OTHER RELEVANT SERVICES DRAWINGS AND CONTRACT DOCUMENTS. ALL EXISTING OR PROPOSED ELEVATIONS (LEVELS) AND DIMENSIONS, ON SITE AND ON DRAWINGS MUST BE CHECKED AND VERIFIED BY THE CONTRACTOR BEFORE THE PREPARATION OF SHOP DRAWINGS OR COMMENCEMENT OF ANY ITEM OF WORK ON THE SITE.ĩ. ONLY WRITTEN DIMENSIONS IN ALL CASES SHALL BE FOLLOWED.Ĩ. ALL DIMENSIONS ARE IN MM AND ANGLES IN DEGREES UNLESS OTHERWISE NOTED.ħ. CONTRACTOR'S SHOP DRAWINGS SHOULD INDICATE ACTUAL ELEVATIONS (LEVELS).ĥ. THE CONTRACTOR SHALL CONDUCT HIS OWN SITE SURVEY OF THE EXISTING GROUND AND CURB ELEVATIONS (LEVELS) AND REPORT ACTUAL ELEVATIONS (LEVELS) TO THE ENGINEER.Ĥ. THE CONTRACTOR SHALL COORDINATE ALL MECHANICAL FLOOR/WALL SLEEVES AND SHAFTS IN CONCRETE SLABS/WALLS WITH MECHANICAL, PLUMBING, FIRE PROTECTION, ELECTRICAL, STRUCTURAL AND ARCHITECTURAL DRAWINGS AND DISCREPANCIES, IF ANY, TO BE BROUGHT TO NOTICE OF THE ENGINEER PRIOR TO EXECUTION OF WORK.ģ. AS INDICATED OR DESCRIBED, THE CONTRACTOR SHALL FURNISH ALL ITEMS REQUIRED FOR THE PROPER EXECUTION AND COMPLETION OF THE WORK.Ģ.

Drawing standard notes full#

THE DRAWINGS DO NOT NECESSARILY INDICATE OR DESCRIBE ALL WORK REQUIRED FOR FULL PERFORMANCE AND COMPLETION OF THE REQUIREMENTS OF THE CONTRACT DOCUMENTS.

THESE DRAWINGS INDICATE IN GENERAL THE PROJECT IN TERMS OF ARCHITECTURAL DESIGN INTENT, THE DIMENSIONS OF THE BUILDING, THE MAJOR ARCHITECTURAL ELEMENTS AND TYPE OF STRUCTURAL,MECHANICAL AND ELECTRICAL SYSTEMS.